This two-hour course ends the detailed review of the 2024 National Fire Protection Association (NFPA) 70E Standard for Electrical Safety in the Workplace.

The 70E Standard is not an Occupational Safety and Health Administration (OSHA) publication. The NFPA created it to fulfill applicable OSHA requirements for safely working with and around electricity.

The 2024 NFPA 70E publication and this course are consistent with the 2023 NFPA 70 National Electrical Code’s requirements. The course is approved by the Oregon Environmental Services Advisory Council.

After completing this course, licensees will be able to:

  • Understand lockout/tagout (LOTO) as a safety protocol.
  • Understand that both simple and complex procedures are recognized by NFPA 70E for LOTO.
  • Explain an arc-flash event while being familiar with hazards to human life resulting from a lack of proper PPE on the job.
  • And more.

Course ID(s): 6160

Approved By: Oregon Environmental Services Advisory Council (OESAC)

  • Electrical Safety (NFPA 70E 2024) Part 2
    • Electrical Safety (NFPA 70E 2024) Part 2 [25 Activities]
      • 01. Section 130.7(D). Other Protective Equipment.
      • 02. Section 130.8(A)-(D). Other Precautions for Personnel Activities.
      • 03. Section 130.8(E)??(N). Other Precautions for Personnel Activities.
      • 04. Section 130.8(O). Alerting Techniques.
      • 05. Section 130.9, Work Within the Limited Approach Boundary or Arc Flash Boundary of Overhead Lines
      • 06. CHAPTER 2, SAFETY-RELATED MAINTENANCE REQUIREMENTS.
      • 07. Article 205, General (Requirements)
      • 08. Article 210, Substations, Switchgear Assemblies, Switchboards, Panelboards, Motor Control Centers, and Disconnect Switches
      • View Additional Activities
        • 09. Article 215, Premises Wiring
        • 10. Article 220, Controller Equipment
        • 11. Article 225, Fuses and Circuit Breakers
        • 12. Article 230, Rotating Equipment
        • 13. Article 235, Hazardous (Classified) Locations
        • 14. Article 240: Batteries and Battery Rooms
        • 15. Article 245, Portable Electric Tools and Equipment
        • 16. Article 250, Personal Safety and Protective Equipment
        • 17. CHAPTER 3, SAFETY REQUIREMENTS FOR SPECIAL EQUIPMENT.
        • 18. Article 310, Safety-Related Work Practices for Electrolytic Cells.
        • 19. Article 320, Safety Requirements Related to Batteries and Battery Rooms.
        • 20. Article 330, Safety-Related Work Practices: Lasers
        • 21. Article 340, Safety-Related Work Practices: Power Electronic Equipment.
        • 22. Article 350, Safety-Related Work Requirements: Research and Development Laboratories
        • 23. Article 360, Safety-Related Requirements for Capacitors.
        • 24. Informative Annex A, Informative Publications.
        • 25. Informative Annex J, Energized Electrical Work Permit.
  • Course Completion
    • Mandatory Questionnaire
    • Certificate of Completion
    • Expedited Reporting Available
Instructor Image

Instructor Bio

Jerry Durham

Jerry previously served the state of North Carolina as a Level III electrical inspector and provided state-approved electrical training for electrical inspectors at both Alamance County and Guilford County (NC) Community Colleges. Jerry taught the Kentucky state-approved four-year electrical apprenticeship programs offered by the Independent Electrical Contractors (IEC) Trade School and Associated Builders and Contractors (ABC) Trade School, and served the state of Kentucky as a Master Electrician and Louisville Metro Code Enforcement Officer. Jerry is a Certified Distance Education Instructor (CDEI) and NCCER Core and Electrical Curriculum certified instructor. Jerry currently holds North Carolina and ICC electrical inspector accreditations and is recognized by the state of Washington as an approved electrical administrator.

Add to Cart